rusteh » user profile

Member Since 20/04/2010
Last Seen 3 hours 5 min
Badges 1
Location VIC

Recent Activities

https://www.3m.com.au/3M/en_AU/p/d/v101182010/
03/05/2024 - 22:10
https://www.3m.com.au/3M/en_AU/p/d/v101182010/
03/05/2024 - 22:09
Nah I mean the QL. I think it's available in both series. I've got a 75xxQL but 6 has it eg https://www.3m.com.au/3M/en_AU/p/d/v101182010/
03/05/2024 - 22:08
Imho, worth the extra $20 or so for the version with the quick release that lets it hang below your chin without removing it. I use mine…
26/04/2024 - 20:22
Geeze I remember paying $120 for this at duty free not long ago. Inflation is a bitch.
24/04/2024 - 17:28
I'm running a 4k 34" non curved Ultra wide + a 24" today. Both are quite old. I'm a software dev, no gaming or graphics works. Would this…
22/04/2024 - 19:31
Got it today, and pulled it apart and compared to a known legit battery, and i'm 100% confident is the real deal. Its exactly the same,…
10/04/2024 - 21:03
Found Amazon selling them for a few bucks more. Could be co-mingled inventory, but will give these a shot, and hope they aren't fake…
08/04/2024 - 14:06
Anyone seen a seller with genuine 5ahs for less than $200 each? It's super difficult to find outside of Total Tools/Sydney tools.
08/04/2024 - 06:27
Anyone compared this and the Max 10? Worth The extra bulk and expense?
02/02/2024 - 21:21
I'm looking for an 8P family tent and was looking at the Coleman, or the Outdoor Connections Bedarra. Anyone compared the two?
22/01/2024 - 16:09
Oh, great idea. I'd not considered that. Might try 3D printing something to suit.
12/09/2023 - 16:18
disagree. variable speed without belt changes is super handy. Especially if you use a mix of materials. Previously I'd be too lazy to…
11/09/2023 - 13:57
Yes. Easily. I've got an ozito mitre saw and if you spend some time to dial it in you can do finish carpentry and furniture. Outdoor stuff…
03/09/2023 - 18:06
I work for an unrelated subsidiary but it forces me into this based on IP address.
12/07/2023 - 20:01
The website indicates you can test a battery while out of a car. Which would be useful. Just not sure how that would work?
07/07/2023 - 12:30
I'm not familiar with these. Is the premise that it can simulate cranking load to get a proper idea of cranking voltage, as opposed to just…
07/07/2023 - 07:22
fixed in v2. I've got the version 2 and its a single stream. Integrated into Home Assistant/Frigate no worries.
03/07/2023 - 16:16
Discount applied at checkout with the code
22/06/2023 - 09:46
Ordered a roll of petg. Anyone able to comment on the quality of this filament?
22/06/2023 - 08:07
Looks like it'll only take one 3.5" drive, is that right?
09/06/2023 - 21:27
Project farm did a video this. Recommended Gear wrench I think.
07/01/2023 - 20:53
Just comes down to what you are using it for. Using it to measure out bits of pine? Fine, use whatever. Want accurate measurements to mill…
19/12/2022 - 14:44
Probably better off with iGaging assuming you aren't going to buy Mitutoyo or Starrett
19/12/2022 - 14:33
I don't really understand why people complain about duty cycle on cheap welders...Has anyone here ever done a continuous weld for 1 minute…
01/12/2022 - 10:47
Fyi Northland doesn't have the one they are showing.
31/10/2022 - 12:10
Worked it out, cheaper one has a Uno R3, more expensive has a Mega 2560 R3, which apparently is slightly more powerful
11/10/2022 - 11:12
Loading...